作者简介：王涛(1982-),男,硕士研究生,主要从事材料加工CAD/CAE方向的研究.
作者单位：王涛（西华大学材料科学与工程学院,四川,成都,610039）
傅建（西华大学材料科学与工程学院,四川,成都,610039）
周盛（西华大学材料科学与工程学院,四川,成都,610039）
彭必友（西华大学材料科学与工程学院,四川,成都,610039）
参考文献：
[1]邢文.注射成型技术进展.现代塑料加工应用,2002,14(4):33.
[2]周国发,等.共注成型充模流动数值模拟研究.中国塑料,2001,15(12):63.
[3]周国发,等.共注成型充模流动的理论模型和模拟.机械工程学报,2003,39(3):94.
[4]Ilinca,Florin.Numerical investigation of the flow front behavior in the co-injection moulding process.International Journal for Numerical Methods in Fluids,2006,50(12):1445.
[5]钟序光,孙懋,张效迅,等.共注成型芯层熔体前沿突破研究.工程塑料应用,2003,31(12):21.
[6]周国发,柳和生,何成宏,等.共注成型芯壳层熔体黏度对芯壳层界面和移动前沿形貌的影响.复合材料学报,2004,21(4):24.
[7]张孝迅,周国发,孙懋,等.顺序共注成型芯层熔体前沿突破的数值模拟研究.中国塑料,2003,17(8):46.
[8]周国发,等.共注成型层厚分布影响因素分析.高分子通报,2002,2(1):45.
[9]匡唐清,等.共注射成型充填过程的运动界面追踪.塑料工业,2005,33(3):32.
[10]Lanvers A,Galuschka S,Tietz W.Injection moulding made transparent-new developments in process simulation.In:16th Colloquium of the German Institute of Rubber Processing(IKV).Aachen:The German Institute of Rubber Processing,1992.6.
[11]Somnuk P,Smith G F.Experiment study of simultaneous co-injection moulding process.In:Proceedings of Annual Technical Confefence (Vol.1):Processing.Boston:The Society of Plastics Engineers,1995.760.
[12]Ilinca F,Derdouri A.Numerical simulation and experimental validation of the filling stage in the co-injection molding process.In:Proceedings of Annual Technical Conference(Vol.1):Processing.Nashville:The Society of Plastics Engineers,2003.627.
[13]Li C J,Lee D J,Isayev A I.Interface development and encapsulation in simultaneous co-injection molding of disk(Ⅱ):Two-dimensianal simulation and experiment.Journal of Applied Polymer Science,2003,88(9):2 310.
[14]王华山,等.共注塑工艺及其制品的设计.中国塑料,2001,15(1):39.
[15]钱欣,等.材料种类对夹芯注射制品残余应力的影响.中国塑料,2006,20(9):45.
[16]Selden R.Co-injection molding:Effect of processing on material distribution and mechanical properties of a sandwich molded plate.Polymer Engineering and Science,2000,40(5):1 165.
[17]Young S A I S,White J AM ES L.A basic experimental study of sandwich injection molding with sequential injection.Polymer Engineering and Science,1980,20(12):798.
[18]周国发,孙懋,柳和生,等.顺序共注成型的实验研究.中国塑料,2003,17(4):53.
[19]孙懋,等.工艺参数对顺序共注成型的影响.中国塑料,2002,16(10):58.
[20]黄峡宏,等.聚合物注塑残余应力的研究进展.力学进展,2000,30(2):272.
[21]周勇飞,等.共注成型制品翘曲变形分析系及其工艺参数的优化.中国塑.2006,20(8):52.
[22]钱欣,等.工艺条件对夹芯注射制品残余应力的影响.中国塑料,2006,20(10):47.
